LE-366 AMD Geode TM LX800 3.5” Embeded Board User’s Manual Edition 1.0 2008/02/20
LE-366 User’s Manual -9- 1.3 <Mechanical Drawing> ‘‘‘‘‘ ‘
LE-366 User’s Manual -10- 1.4 <Block Diagram> FlashBIOS (SST FWH) 16Mbx16 DDR DIMMMiniPCI SLO
LE-366 User’s Manual -11- Chapter 2 <Hardware Setup> 2.1<Connector Location>
LE-366 User’s Manual -12- <Jumper Reference> Jumper Function JP1 LVDS Panel Voltage Selection (+5V
LE-366 User’s Manual -13- 2.1.1 <Connector Reference> Connector Function Remark CN1 VGA Display / Au
LE-366 User’s Manual -14- 2.2 <CPU and Memory Setup> 2.2.1 <CPU Setup> The board integrates AMD G
LE-366 User’s Manual -15- 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the boar
LE-366 User’s Manual -16- 2.3 <Enhanced IDE & CF Interface> The board has one Ultra DMA33 IDE inter
LE-366 User’s Manual -17- 2.4 <Floppy Port> The board provides a slim type floppy port; please use the
LE-366 User’s Manual -18- 2.8 <Onboard Display Interface> The board integrates AMD Geode LX800 processo
LE-366 User’s Manual -1- Copyright Copyright 2006. All rights reserved. This document is copyrighted and all rights are res
LE-366 User’s Manual -19- 2.4.2 <Digital Display> The board provides one 30-pin LVDS connector for 1
LE-366 User’s Manual -20- Connector: CN_LVDS (CN2) (for 18 bit Single channel LVDS panel) Type: 30-pin heade
LE-366 User’s Manual -21- To setup the LCD, you need the component below: 1. A panel with LVDS interfaces
LE-366 User’s Manual -22- After setup the devices well, you need to select the LCD panel type in the BIOS.
LE-366 User’s Manual -23- <USB2.0 Interface> Based on AMD CS5536, the board provides 2 x USB2.0 por
LE-366 User’s Manual -24- 2.5 <GPIO Interface> The board provides a programmable 8-bit digital I/O i
LE-366 User’s Manual -25- 2.6 <Serial Port Jumper Setting > The COM1 RS232 serial port, with jumper
LE-366 User’s Manual -26- 2.7 <Power and Fan Connector> The LE-366 provides a standard ATX power supp
LE-366 User’s Manual -27- 2.7.3 <Fan Connector> Connector: SYSFAN Type: 3-pin fan wafer connector
LE-366 User’s Manual -28- 2.8 <Indicator and Switch> The JFRNT provides front control panel of the bo
LE-366 User’s Manual -2- Packing List Please check the package before you starting setup the system. Hardw
LE-366 User’s Manual -29- (This Page is Left For Blank)
LE-366 User’s Manual -30- Chapter 3 <BIOS Setup> The motherboard uses the Award BIOS for the sy
LE-366 User’s Manual -31- (This Page is Left for Blank)
LE-366 User’s Manual -32- Appendix A <I/O Port Pin Assignment> A.1 <IDE Port> Connector: J6 Type: 44-p
LE-366 User’s Manual -33- A.2 <Floppy Port> Connector: FDD1 Type: 26-pin connector Pin Assignment Pin
LE-366 User’s Manual -34- A.4 <CRT Port> Connector: CRT Type: 15-pin D-sub female connector on I/O Panel
LE-366 User’s Manual -35- A.7 <PS/2 Keyboard & Mouse Port> Connector: Mouse / Keyboard Type: 6-pi
LE-366 User’s Manual -36- (This Page is Left for Blank)
LE-366User’s Manual -37- Appendix B <Flash BIOS> B.1 BIOS Auto Flash Tool The board is based on
LE-366 User’s Manual -38- Appendix C <System Resources> C1. <I/O Port Address Map>
LE-366 User’s Manual -3- Index Chapter 1 <Introduction>...
LE-366 User’s Manual -39-
LE-366 User’s Manual -40- C2. <Memory Address Map>
LE-366 User’s Manual -41- C3. <System IRQ Resources>
LE-366 User’s Manual -42- Appendix D <Programming GPIO’s> The GPIO can be programmed with the MSD
LE-366 User’s Manual -43- Appendix E <Watch Dog timer Setting > The watchdog timer makes the system au
LE-366 User’s Manual -44- (This Page is Left for Blank)
LE-366 User’s Manual -4- A.7 <PS/2 Keyboard & Mouse Port>...
LE-366 User’s Manual -5- (The Page is Left For Blank)
LE-366 User’s Manual -6- Chapter 1 <Introduction> 1.1 <Product Overview> LE-366 is the Mini-
LE-366 User’s Manual -7- 1.2 <Product Specification> General Specification Form Factor 145 mm x 10
LE-366 User’s Manual -8- Connector External Audio phone jack for Line-out and MIC-in. Onboard audio conn
Kommentare zu diesen Handbüchern